Z Purlin Roll Forming Machine
Z purlin Roll forming machine is a production line for making Metal Z purlin profiles.
How to maintenance of Z-shaped steel machine equipment
1. Always check the fasteners for looseness and fasten them in time.
2. Frequently check the transmission components for jamming and timely maintenance.
3. Regularly check the electrical parts for abnormal noise, odor, fever, etc. If abnormality is found, the power supply should be cut off immediately, and refer to the instruction manual for troubleshooting methods. 3. According to different spans of the building, the size of the load, the thickness of the supporting beams, etc., the thickness selected is also different. The longitudinal direction of the slab should be placed parallel to the main beam, and the edge of the joint between the slab and the slab should fall on the same beam The length of the self-tapping screws for fixing is the board thickness plus 30-35mm.
Full-automatic roll forming machine processing customization
Between 300-600mm, the center of the nail holes around the board should be about 20mm from the edge of the board. 6. Because the kitchen and bathroom are considered to be waterproof, and the area is small, the static and dynamic load requirements are slightly smaller, so the thickness of the board can be slightly thinner, and the type of the selected profile can also be judged accordingly. Nowadays, in the economic market wave, the survival environment of enterprises is very difficult. Especially for small enterprises, because the capital chain is not large enough, many cold roll forming machinery manufacturers frequently close after opening. The high user demand for products is also one of the main reasons for accelerating the closure of small businesses. People nowadays have more and more requirements on the materials, shapes and dimensions of products. Therefore, the companies engaged in cold-bending machinery will only remove some of the industry's elites and large enterprises to survive. The diversification of products will also cause the diversification of materials.
What is the angle of the z purlin profiles
The angles of Z purlins and C channel are different, C channel steel is 90 degrees, Z-shaped steel is less than 90, roughly 60 to 75 degrees, so when a certain slope roof is used for purlins, it is necessary to consider the purlins with the knowledge of the force The angle problem, the use of Z-shaped slope can make full use of its bending performance. Configure a reasonable number of palletizing to ensure the number of palletizing at a time, but also ensure the quality of palletizing. Able to complete the amount of palletizing in a short time. Second, in the process of palletizing, a large amount of waste material will be generated on the belt, and the treatment of these waste materials by traditional palletizing equipment is often more troublesome.
How to maintenance of Z-shaped steel machine equipment
1. Always check the fasteners for looseness and fasten them in time.
2. Frequently check the transmission components for jamming and timely maintenance.
3. Regularly check the electrical parts for abnormal noise, odor, fever, etc. If abnormality is found, the power supply should be cut off immediately, and refer to the instruction manual for troubleshooting methods. 3. According to different spans of the building, the size of the load, the thickness of the supporting beams, etc., the thickness selected is also different. The longitudinal direction of the slab should be placed parallel to the main beam, and the edge of the joint between the slab and the slab should fall on the same beam The length of the self-tapping screws for fixing is the board thickness plus 30-35mm.
 |
| Z purlin |
Full-automatic roll forming machine processing customization
Between 300-600mm, the center of the nail holes around the board should be about 20mm from the edge of the board. 6. Because the kitchen and bathroom are considered to be waterproof, and the area is small, the static and dynamic load requirements are slightly smaller, so the thickness of the board can be slightly thinner, and the type of the selected profile can also be judged accordingly. Nowadays, in the economic market wave, the survival environment of enterprises is very difficult. Especially for small enterprises, because the capital chain is not large enough, many cold roll forming machinery manufacturers frequently close after opening. The high user demand for products is also one of the main reasons for accelerating the closure of small businesses. People nowadays have more and more requirements on the materials, shapes and dimensions of products. Therefore, the companies engaged in cold-bending machinery will only remove some of the industry's elites and large enterprises to survive. The diversification of products will also cause the diversification of materials.
What is the angle of the z purlin profiles
 |
| C channel |
The angles of Z purlins and C channel are different, C channel steel is 90 degrees, Z-shaped steel is less than 90, roughly 60 to 75 degrees, so when a certain slope roof is used for purlins, it is necessary to consider the purlins with the knowledge of the force The angle problem, the use of Z-shaped slope can make full use of its bending performance. Configure a reasonable number of palletizing to ensure the number of palletizing at a time, but also ensure the quality of palletizing. Able to complete the amount of palletizing in a short time. Second, in the process of palletizing, a large amount of waste material will be generated on the belt, and the treatment of these waste materials by traditional palletizing equipment is often more troublesome.
Super… i really like your blog…
ReplyDeleteHow much this machine and material thickness
ReplyDelete